-
A single component, solvent free, very low viscosity, hydrophobic polyurethane water cut-off grout. . This product is specifically engineered for use in concrete, water bearing structures, or sandy environments to stop gushing water or water seepage including cracks in concrete where the structure is not subject to movement. It is formulated to react with water to form a rigid polyurethane closed cell foam that molds to substrate and stabilize surrounding soils to help its load bearingcapabilities. Characteristics: - Very low viscosity (110 - 130 cps) - Rapid compressive strength gains - Resistant to biological attack - Pumped as a single component - Reacts with water to form a close-cell watertight foam - Up to 2900% expansion - Variable reaction (set) time with the use of an accelerator - Capable of closing gushing leaks to watertight Uses Include: - Sealing leaks and filling wide gaps in concrete such as box culverts - Sealing tunnels (subway, water, utility, etc.) - Seals manholes, sanitary and storm pipe structures - Curtain grouting below grade structures in parking decks, foundations, and basements - Permeation grouting for soil stabilization in roads, highways, seawalls, and retaining walls -
A rapid setting, two component, 100% solids structural epoxy for anchoring rods, bars and bolts in concrete, as well as filling cracks and setting ports for epoxy injection. Five Star RS Anchor Gel is a nonsag, moisture insensitive epoxy adhesive that can be used for both vertical and horizontal installations. This system offers chemical resistance, excellent adhesion and rapid strength gain. Characteristics: - Low VOC - Low odor - Moisture insensitive, can be used in wet environments - Excellent adhesion to masonry, concrete, wood, steel and most structural materials - Gel consistency ideal for vertical, overhead and non-mating surfaces - Fast strength gain - Convenient 1:1 mixing ratio - Convenient cartridge and bulk packaging - Meets ASTM C881 Types I, II, IV, and V, Grade 3, Classes B & C standards
-
A two component, 100% solids, moisture insensitive, structural epoxy used in filling cracks up to 1/2" wide. It is a smooth, nonabrasive gel that can be pressure injected or hand applied above grade or underwater. Characteristics: - Low VOC - Excellent adhesion to concrete, masonry, wood, steel, and most structural substrates - High strength - Gel consistancy for vertical and overhead applications - Moisture insenitive - Convenient 1:1 ratio mix design - Unique nonabrasive texture permits applications with automated dispensing equipment - Packaged as a plural component cartridge (22oz.-600ml) or bulk units (2 gallon pails) Uses Include: - Sealing PileForm F Fiberglass jacket seams - Pressure injection of cracks in structural concrete, masonry, wood, and othe substrates - Surface repair of non-moving cracks on new or existing structures - Anchoring of bolts, dowels, pins, and special fasteners - General purpose adhesive - Re-pointing concrete block and timber drydocks
-
MST has a series of epoxy compounds that are used to fill very large voids in machinery baseplates, pumpbases, and any other type of void area. This includes products such as Chockfast Gray, Chockfast Red HF, Five Star DP/PG, Five Star Fuid Epoxy, etc. Give us a call with your application and we'll make a recommendation of product for your application.
-
This one piece port fits in a 1/2" diameter drilled hole in a concrete surface. It is used when the surface is to irregular for the use of our standard surface port or the surface of the concrete is to contaminated and allows the resins to penetrate into cracked structure below the contaminated surface area. It will accept resins from either a two component pump system or our cartridge systems using a static mixer and a quik-connect fitting.
-
This one piece port fits in a 1/2" diameter drilled hole in a concrete surface. It is used when the surface is to irregular for the use of our standard surface port or the surface of the concrete is to contaminated and allows the resins to penetrate into cracked structure below the contaminated surface area. It will accept resins from either a two component pump system or our cartridge systems using a static mixer and a quik-connect fitting. -
This one piece port is designed to inject our resin systems into a corner application. It will accept resins from either a two component pump system or our cartridge systems using a static kixer and a quik-connect fitting. This port works well for cracks and seperations between abutting elements such as walls and floors, or steel plates and concrete.
-
This two piece port uses a port porting adapter (LPP) and and a polyethylene tee (LPT). The pedestal is bonded to the surface using a two component adhesive. The barbed tee fits over the pedestal inlet tube and allows for multiple injection ports via manifolding with one fill spot. Once the void is full the black tee (LPT) is pushed down to seal the port and prevent drainage during the resin cure process.
-
This one piece port is designed to inject our resin systems into any surface application. It will accept resins from either a two component pump system or our cartridge systems using a static mixer and a quik-connect fitting. This port will withstand pressures up to 900 psi. A perforated base allows it to be positioned easily over a crack or drilled hole. This port works well for vertical, horizontal, or overhead applications such as flat wall surfaces, floors, baseplates, soleplates, or any other injection process where accessability is good. It will accept resins from either a two component pump system or our cartridge systems using a quik-connect fitting.
-
MST has a series of manual injection guns to cover any application of our resin systems. From a standard caulking gun (1:1 ratio) for very low viscosity resins up to (26:1) ratios for high viscosity resins, joint fillers and mastics. Our (14:1 ratio) gun is excellent for our uni-cartridge resin systems. We also have a series of plural component guns for our dual cartridge resin systems and bulk guns for large volume product applications. Each gun is designed and manufactured to an ergonomic design for continued use without operator fatigue.
-
A manual plural component caulking gun with a 26:1 thrust ration for ergonomic user application comfort. Can utilize the following plural component sizes: 300ml x 300ml, 300ml x 150ml, 150ml x 150ml, 150ml x 75ml Easily converts to various cartridge sizes with snap-in, snap-out push discs.
-
A manual plural component caulking gun with a 26:1 thrust ration for ergonomic user application comfort. Designed specifically for 750ml x 75ml plural component cartridges
-
A standard manual caulking gun for 10 oz. or 30 oz. cartridges with a 12:1 piston ratio for ergonomic applicator comfort.
-
A standard caulking gun for 10 oz. or 30 oz. cartridges with a 15:1 piston ratio "High Thrust" for ergonomic applicator comfort.
-
A standard caulking gun for 10 oz. or 30 oz. cartridges with a 15:1 piston ratio "High Thrust" for ergonomic applicator comfort.
-
An air driven pneumatic applicatior for low viscosity resin sytems utilizing 10 oz. empty cartridges for filling with desired product or from pre-packaged materials. Utilizes 100 psi service air and has a built-in air pressure regulator for dispensing control.
-
An air driven pneumatic applicatior for low viscosity resin sytems utilizing 30 oz. empty cartridges for filling with desired product or from pre-packaged materials. Utilizes 100 psi service air and has a built-in air pressure regulator for dispensing control.
-
A rod driven pneumatic applicatior for low viscosity resin sytems utilizing 10 oz. empty cartridges for filling with desired product or from pre-packaged materials. Utilizes 100 psi service air and has a built-in air pressure regulator for dispensing control.
-
A rod driven pneumatic applicatior for low viscosity resin sytems utilizing 30 oz. empty cartridges for filling with desired product or from pre-packaged materials. Utilizes 100 psi service air and has a built-in air pressure regulator for dispensing control.
-
A pneumatic powered caulking gun for low viscosity resin and polyurethane systems. Produces 490 lbs. of thrust @ 100 psi service air pressure. Capable of handling plural component cartridges size including 300ml x 300ml, 300ml x 150ml, 150ml x 150ml, and 300ml x 75ml. Easily converts with Snap-in/Snap-off push disks. Gun has adjustable pressure regulator built in and a air dump valve that stops flow immediately. Also has a reverse air control for withdrawing product on overfill.
-
A pneumatic powered caulking gun for medium to high viscosity resin, polyurethane systems, sealers, and joint compounds. Produces 1,100 lbs. of thrust @ 100 psi service air pressure. Capable of handling plural component cartridges size including 300ml x 300ml, 300ml x 150ml, 150ml x 150ml, and 300ml x 75ml. Easily converts with Snap-in/Snap-off push disks. Gun has adjustable pressure regulator built in and a air dump valve that stops flow immediately. Also has a reverse air control for withdrawing product on overfill.
-
A pneumatic powered caulking gun for medium to high viscosity resin, polyurethane systems, sealers, and joint compounds. Produces 1,100 lbs. of thrust @ 100 psi service air pressure. Capable of handling plural component cartridges size including 750ml x 750ml, 750ml x 300ml, 750ml, 75ml x 150ml, 600ml x 600ml, 600ml x 300ml, and 300ml x 300ml. Easily converts with Snap-in/Snap-off push disks. Gun has adjustable pressure regulator built in and a air dump valve that stops flow immediately. Also has a reverse air control for withdrawing product on overfill.
-
MST has a series of pneumatic injection guns for projects requiring multi port injections or very large volumes of resin product that require an operator to inject over a long period of time. Each of these guns are designed to accept our unicartridge, single cartridge, or plural component cartridges as well as bulk dispensing for large projects. Each gun is manufactured to an ergonomic design for continued use and air pressures are adjustable to control product flow. Each gun has an air dump valve that stops product flow instantly. Suitable for 100 psi supply air with various thrust ratios depending on the product that is being dispensed.
-
Pro-Poxy 400 is a two component 100% solids, moisture tolerant, all weather epoxy acrylate hybrid anchoring gel. Pro-Poxy 400 is formulated for rapid set up at room temperatures and down to temperatures of -15?F (-26?C). Pro-Poxy 400 is ideal for anchoring dowels, bolts, threaded rod, pins and reinforcement steel in concrete. Pro-Poxy 400 can also be used in cooler and freezer applications or anywhere low temperature installations are required. Ideal for setting injection ports and sealing cracks for the pressure injection process. Characteristics: - High modulus epoxy gel, high strength structural adhesive - Ideal for anchoring dowels, bolts, reinforcing steel, and threaded rod - Moisture tolerant - Fast setting, non sag gel - V.O.C. Compliant (0 g/l) Meets Federal EPA, OTC, LADCO, SCAQMD, & CARB regulations - Packaged in plural component uni-cartridges or dual cartridges - High chemical resistance - Meets ASTM C-881/AASHTO M-235, Types I, II, IV, V Grade 1, Classes A, B & C - Excellent adhesion to most construction materials - All weather and temperature installation - Ideal for cold weather installations - Styrene free
